If there is anything positive in littering (and, really, there isn’t–let’s just make that clear here) it’s that nature can do some amazing things with what she’s given.
Case in point: Sea Glass
What starts off as glass bottles, plates, or other glassware and ends up in the oceans or bays gets tossed and tumbled by waves and sand and a worked on by the salty waters to wash up on shores as beautifully frosted bits and pieces, ready to fuel creative daydreams.
Sea (or beach) glass is getting tougher to find in many areas–and that’s not necessarily a bad thing as it means there’s less littering going on–but in the scarcity some folks have stepped up to manufacture imitation beach glass for crafters. You can also achieve a similar look by using a frosting or etching medium on whatever glass you like, and even spray paints are out now that will do the trick in a pinch.
If a recent trip through both Crate & Barrel and West Elm is any indication, those frosted blues and greens are going to seen a lot this summer. If you’re not interested in a room makeover, how about adding something new to your jewelry wardrobe instead?
Many years ago, I traded a fellow creative some stuff I had that I didn’t need (I couldn’t even tell you what it was, it’s been so long) for a small box of sea glass. I’ve carried it with me through several moves, always wondering what I might do with it. I think I used a few pieces in my mosaic project a while back, but mostly I just like to run my hands through it and enjoy the frosted finish and water-worn edges.
Except this one particular piece of green sea glass that fits perfectly along the curve of my index finger. That piece I’ve always wanted to turn into a ring.
And today’s the day I do that. Wanna see how?
To make a similar ring you’ll need:
- Beach or Sea Glass
- Jewelry Wire
- Pliers and Wire Cutters
- Ring Mandrel (optional but useful)
Start with 4 pieces of jewelry wire (I’m using 24G Sterling Silver round wire) about 9 inches long each and sort of weave them together, 2×2, in the center or as close as you can manage.
If you’re using flat or square wire, this might be a smidgen easier, but I’m using what I’ve got in the craft stash, so mine wanted to roll around a lot. To stop the rolling I twisted each pair of ends 1/4- to 1/2-inch or so (not much wider/taller than your beach glass) to lock everything into place and then gently pushed the centers down with my pliers to set them into place.
Fit the center of your wires to the center of your glass (more or less) and then fold the top and bottom “arms” over the top and bottom of your glass. If the arms out to each side are twisted beyond the edges of your glass, gently untwist them so that they separate right where the glass ends.
To secure the glass in place, we’re going to take each wire from the top arm and pull it over to the opposite side, snugging it where the twists stop. Then do the same for the bottom. This really makes it look like some sort of spidery thing from the top, and from the underside of the glass your wires should be forming a diamond shape, locking the corners into the place.
Twist the wires at each side together, 2 at a time and very close to the side of the glass, to secure each corner, then twist all 4 wires of each side together to the ends. It may not look perfect but, hey, neither does the tumbled glass, right? Go with the wonky, tilted, organic swoopy flow of things. Now you have a wrapped piece of beach glass with two twisty arms.
Forming the twisted arms into the band is, I admit, one of the more fiddly bits of this process. Start by bending each arm around the finger you plan to wear it on to get the best fit possible. This is where having a ring mandrel comes in handy, by the way, as once you know the size you can use both hands to finish the ring rather than only one. Wrap the end of one arm around the beginning of the other, right where it meets the side of the glass, and crimp well with your pliers. Do the same with the other arm on the other side, trying not to twist the bands together for a gentler fit.
That’s how it’s supposed to go at least–it took me a couple of tries to get this one right but with patience I prevailed. When working with twisted metal wire you have to be careful Â not to work the wire too much or itÂ will break on you.
Once finished, slip it on and admire your handiwork!
I think I might just need to wear green tomorrow to have an excuse to wear my new piece of jewelry!
Thanks for your patience while I finished up a rush design order and my posting got a bit spotty. I’ll be doing my best to catch us up to where I wanted to be over the next couple of weeks.